Ask our experts a question about this model and we'll get back to you as soon as possible!
43 questions answered by our experts.
Sort by:
- < Prev
- 1
- 2
- 3
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Tammy
December 21, 2021
When starting cycle agitators sencing washing complete
For model number MVW7232HW0
Hello Tammy, thank you for your question. It sounds like the lid switch might be broken. Unplug the appliance from the electrical outlet before you begin. Set your multimeter to the lowest ohms of resistance and test your lid switch. If it does not read any continuity, then your lid switch is indeed faulty. Part number PS12730859. You cold also test the water level switch. The water level switch has three terminals. Test them for continuity in pairs. First, touch the meter probes to terminals 1 and 2. Note the reading, which should be either 8 (infinity, which means no continuity) or some value close to 0.0 (continuity). Analyze the results of the continuity tests: Two of the pairs should have no continuity, and one should have continuity. If you get a different result, the switch is bad and needs to be replaced. Part number PS12348295. We hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
SWITCH
$37.93
In Stock
LID SWITCH ASSEMBLY
$50.01
Special Order
Saah
March 2, 2023
may washer shakes all over when spinning as told i need to replace the socks is that what is called the rods . if so how many rods are there per washer. also are they all sold separtly or all together ?
For model number MVW7232HW0
Hi Saah,Thank you for your question. There are 4 rods in your washer. The part number listed for the suspension rod kit is PS12731247. If you would like to place an order for it, please call our customer service line and anyone will be happy to assist you. We look forward to hearing from you!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Suspension Kit - Set of 4
$86.46
In Stock
Janice
April 20, 2023
I NEED A LID LOCK IT FELL OFF
For model number MVW7232HW0
Hi Janice, thank you for writing. The Lid Lock Assembly for this model is PartSelect Number PS12731130. Good luck with the repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Jim
June 14, 2023
With 1 minute left during the spin cycle the spinning cycle changes to sensing and an excruciating noise starts and lasts for the remainder of the time or pressing pause or cacel.buttons to stop the washer.
For model number MVW7232HW0
Hi Jim, thank you for reaching out. We have found that the only thing that can cause your issue is the motor control board, part number PS12745529. We hope this information helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
CNTRL-ELEC
$525.37
In Stock
Michael
December 9, 2023
What does F8EI code on console mean. Some times it shows no water , but I know there is water.
For model number MVW7232HW0
Hello Michael, thank you for your inquiry. We have researched and found that the error code F8EI indicates a problem with the water supply. We would recommend checking the water supply to the washer. If this does not resolve the issue, then you may need to check the control board, part number PS12745529, to solve the problem. We hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
CNTRL-ELEC
$525.37
In Stock
- < Prev
- 1
- 2
- 3
- Next >
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Parts Used:
-
Michelle from Richardson, TX
-
Difficulty Level:
Really Easy
-
Total Repair Time:
Less than 15 mins
65 of 129 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Tab on door strike got broken off and washer would not operate without it.
Pushed in on door strike and rotated it counterclockwise, removed broken strike and installed new strike. NOTE: when removing the old strike (turning counterclockwise) it felt like it might break and/or was attached with an screw that I didn't see but it came right out.
Parts Used:
-
John from AURORA, CO
-
Difficulty Level:
Very Easy
-
Total Repair Time:
Less than 15 mins
24 of 30 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Snapped off door strike
Super easy repair, simply turn the broken door strike counterclockwise to remove; insert the new door strike into the slots and turn clockwise to lock into place.
Parts Used:
-
Miranda from WEST FARGO, ND
-
Difficulty Level:
Very Easy
-
Total Repair Time:
Less than 15 mins
10 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
